KONFIGURASI DYNAMIC ROUTING OSPF

KONFIGURASI DYNAMIC ROUTING OSPF

Assalamualaikum wr.wb
yang dimaksud OSPF ?

 Ospf Merupakan Sebuah Routing Protokol Berjenis IGP yang hanya dapat berkerja Dalam jaringan Internal Suatu Organisasi Atau Perusahaan.

Disini saya akan membahas tentang ospf...Berikut topologinya!!!

Berikut Topologinya

1. Lalu pilih router 1, berikan ip addres, nama dan di setiap interface pada router 1.

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#int f0/0
R1(config-if)#ip add 12.12.12.1 255.255.255.0
R1(config-if)#ex

R1(config)#no sh

2. Kemudian anda ke router 2, ip adress , nama dan di setiap interface pada router 2.

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#int f0/0
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#sh
R2(config-if)#no sh

R2(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R2(config-if)#ex
R2(config)#int f1/0
R2(config-if)#ip add 23.23.23.1 255.255.255.255
Bad mask /32 for address 23.23.23.1
R2(config-if)#ip add 23.23.23.1 255.255.255.0
R2(config-if)#no sh

3.kemudian ke router 3,ip addres nama dan di setiap interface pada router 3.

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#int f1/0
R3(config-if)#ip add 23.23.23.2 255.255.255.0
R3(config-if)#no sh

R3(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

R3(config-if)#ex
R3(config)#int f0/0
R3(config-if)#ip add 24.24.24.1 255.255.255.0
R3(config-if)#no sh

R3(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

R3(config-if)#ex
R3(config)#int f2/0

R3(config-if)#ip add 35.35.35.1 255.255.255.0

4.kemudian ke router 4,ip addres, netmask ,nama dan di setiap interface pada router 4.

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R4
R4(config)#int f0/0
R4(config-if)#ip add 24.24.24.2 255.255.255.0
R4(config-if)#no sh

R4(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R4(config-if)#ex
R4(config)#int f1/0
R4(config-if)#ip add 45.45.45.1 255.255.255.0

R4(config-if)#no sh

5. Lalu ke router 5,ip add, netmask,nama dan di setiap interface pada router 5

Router(config)#hostname R5
R5(config)#int f2/0
R5(config-if)#ip add 35.35.35.2 255.255.255.0
R5(config-if)#no sh

R5(config-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

R5(config-if)#ex
R5(config)#int f1/0
R5(config-if)#ip add 45.45.45.2 255.255.255.0
R5(config-if)#no sh

R5(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

R5(config-if)#ex
R5(config)#int f0/0
R5(config-if)#ip add 56.56.56.1 255.255.255.0
R5(config-if)#no sh

6. Kemudian router 6, ip addres , netmask, nama dan di setiap interface pada router 6.

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R6
R6(config)#int f0/0
R6(config-if)#ip add 56.56.56.2 255.255.255.0
R6(config-if)#no sh

R6(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R6(config-if)#ex
R6(config)#int f1/0
R6(config-if)#ip add 67.67.67.1 255.255.255.0
R6(config-if)#no sh

7. Terakhir router 7, ip address, netmask, nama dan di setiap interface pada router 7.

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R7
R7(config)#int f1/0
R7(config-if)#ip add 67.67.67.2 255.255.255.0

R7(config-if)#no sh

8. Kemudian kita melakukan loopback pada setiap router 1 sampai 6 dibawah ini namun di bedakan ip adress seperti router 1 menjadi (1.1.1.1) dan di setiap router seperti router 1.dan di bawah ini contohnya

9. Setelah kita melakukan loopback,kemudian kita melakukan router ospf pada setiap router. saya akan memberikan contohnya seperti di bawah ini!

R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#router ospf 5
R1(config-router)#net 12.12.12.0 0.0.0.255 area 1
R1(config-router)#net 1.1.1.1 0.0.0.0 area 1

 4.jika sudah bisa dicoba dengan cara menge-ping atau mengirim pesan pada setiap router

.

as

Demikian penjelasan Konfigurasi Dynamic Routing OSPF,kurang lebihnya mohon maaf ASSALAMUALAIKUM WARRAHMATULLAHI WABARAKATUH